Home › Guides

Tire markings, explained: every groove and every sidewall code

Tire markings, explained: every groove and every sidewall code

A tire talks. Almost everything you need to judge it is printed or molded into the tire itself — half of it in the tread, half of it on the sidewall. The problem is that it speaks in codes and symbols, and nobody at the shop has time to translate.

This guide is the translation. After it, you will be able to walk up to any tire, read it, and know what it is built for, how much it can carry, how fast it is rated to go, when it was made, and whether it is worn out.

225/65R17 102H RADIAL · TUBELESS MAX PRESS 44 PSI DOT 4B1X 2324 M+S The size: width / sidewall height / wheel diameter Load index & speed symbol 102 = max load per tire · H = rated up to 130 mph DOT code last 4 digits = week & year it was made (2324 = week 23, 2024) 3PMSF — the snowflake on the mountain tested severe-snow rating. M+S alone is not a test. Max pressure the tire's limit — your car's placard pressure is the one to use Rotation arrow directional tires must roll this way UTQG grades treadwear · traction · temperature — also on the sidewall & our pages THE TREAD, UP CLOSE Circumferential grooves move water out — your wet grip Tread blocks & sipes the thin cuts bite on wet, ice & snow Wear bar (TWI) flush with the bar = 2/32 in — replace Shoulder blocks cornering grip & off-road bite
Every marking that matters, on one tire — and the tread, up close. Diagram drawn by TireDoc.

Part one: the tread

The tread is the patterned rubber that touches the road. Every element of the pattern has a job.

Circumferential grooves. The long channels that run around the tire, usually three or four of them. Their job is water. At speed, they channel water out from under the tire so the rubber can keep touching the road instead of floating on it — that floating is aquaplaning, and it is the grooves that stand between you and it. Deep, wide grooves are a wet-weather feature.

Lateral grooves. The channels that run across the tread, often angled. They feed water sideways into the circumferential grooves and add edges that bite when you accelerate and brake. On all-terrain tires they are bigger and more open, because there they also have to dig into dirt and gravel and clean mud out of themselves.

Tread blocks. The raised chunks of rubber between the grooves. Their size and stiffness set the tire's character. Big, stiff, closely packed blocks are quiet and stable on the highway. Smaller, more separated blocks flex and bite better on loose or slippery surfaces — and hum more on asphalt.

Sipes. The thin slits cut into the tread blocks — they look like knife cuts. A sipe opens as the block flexes, presenting hundreds of extra tiny edges. Those edges are what grip on wet roads, ice and light snow. Winter and all-weather tires are covered in them; a summer performance tire has few. If you want one visual clue to a tire's cold-weather intent, count the sipes.

Shoulder blocks. The blocks at the two outer edges. They do the work in corners, and on all-terrain tires they wrap slightly down the sidewall to bite in ruts and protect the tire's shoulder from rocks.

Wear bars — the TWI indicators. Inside the main grooves, at regular intervals, sit small raised bars of rubber. TWI stands for tread wear indicator, and you will find the letters TWI, or a small triangle, on the sidewall pointing at each one. When the tread wears down until it is level with those bars, the tire is at 2/32 of an inch — the legal minimum in most states, and well past the point where wet grip has faded. Level with the bar means replace, not "soon".

The pattern's shape. Three layouts cover nearly everything. A symmetric pattern is the same on both halves and can be rotated any way. An asymmetric pattern has a different inner and outer side — the sidewall will say "outside", and it must be mounted that way. A directional pattern is a V or arrow shape built to roll one way only, usually for moving water; it carries a rotation arrow, below.

Part two: the sidewall

Everything here is molded into the rubber in raised letters. Some of it is on both sidewalls; the full DOT code, by rule, may be complete on only one side — check both.

The size. The big string, like 225/65R17 102H. Width, sidewall height, wheel diameter — then the load index and speed symbol. It deserves its own walk-through, and it has one: how to read your tire size.

Load index. The number after the size — 102 in the example. It is a code for the maximum weight one tire can carry: 102 means 1,874 pounds. Four tires must together carry your vehicle and everything in it, which is why you never fit a tire with a lower load index than the one your vehicle came with. If the letters XL (extra load) appear, the tire is a reinforced version that carries more at higher pressure.

Speed symbol. The letter — H in the example. It is the maximum speed the tire is built and tested to sustain: S is 112 mph, T is 118, H is 130, V is 149. It is not a suggestion to drive there. It is also a rough fingerprint of the tire's construction and heat resistance, which is why it should never be lower than your vehicle's original rating either.

UTQG grades. Three ratings, printed together: treadwear (a number like 600), traction (AA, A, B or C) and temperature (A, B or C). One warning matters more than the numbers: the treadwear grade is assigned by the manufacturer itself, so it only compares fairly against the same brand's tires. We explain UTQG honestly, in its own guide.

DOT code and the date. Every tire sold in the US carries a DOT code. The part you want is at the end: four digits giving the week and year of manufacture. 2324 means week 23 of 2024. This matters because rubber ages even on a shelf. A "new" tire that is already five years old is not new in the way that counts — check the date on the actual tires being fitted, not just the model name.

M+S and the snowflake. M+S (mud and snow) is a tread-pattern designation the manufacturer applies itself; there is no test behind it. The three-peak mountain snowflake — 3PMSF — is different: the tire passed a regulated snow-traction test. In real snow, the snowflake is the marking that means something. The difference between these two is the difference between all-season and all-weather tires.

Maximum pressure. "MAX PRESS 44 PSI" is the highest pressure the tire itself can hold — a limit, not a target. The pressure you should actually run is the one on your vehicle's door-jamb placard, set by the people who built the car. Same for load: "max load" on the sidewall is the tire's ceiling, not your car's instruction.

Rotation arrow. On directional tires, an arrow marked "rotation" shows which way the tire must roll. Mounted backwards, a directional tire pumps water the wrong way. If your tires have arrows, a glance after any rotation or repair tells you whether the job was done right.

Maker's marks. You may also see small codes for original-equipment fitments — a star for BMW, MO for Mercedes, and so on — meaning that version of the tire was tuned for that maker. Same model name, slightly different tire. Worth knowing when a price looks oddly good.

Reading a tire in sixty seconds

When you look at a tire — in a store, or on your own car — run this order:

That is the whole language. The codes were never meant to hide anything — they just needed someone to read them out loud.

Next step: put it into practice — find the 3 tires for your car, or read how we recommend.

Not sure which tire fits your car? Answer a few questions — your car, your city, your roads — and get exactly 3 tires, honestly compared.

Find your 3 tires →